If submitting a service request after hours or on the weekend, please note it is best to call.

(210) 675-8366 Emergency Service Available Request Service
×

How Does My Gas Furnace Work?

February 18, 2021 | Blog

Although todayโ€™s furnaces can generate heat using a variety of fuels, natural gas is one of the most popular. Natural gas furnaces typically use a combination of methane and other carbon-based gases.

Our professionals at KCA Services encourage you to understand how your gas furnace works so you can spot any potential problems in your Boerne homeโ€™s heating system.

The Thermostat

Although you could argue your gas furnace begins the house-heating process when you turn on your heating, ventilation, and air conditioning (HVAC) system, the reality is that in most homes, the thermostat really runs the show.

A thermostat is a temperature-activated switch that communicates your homeโ€™s temperature to the gas furnaceโ€™s control board. Once you program your thermostat to a particular temperature, your HVAC system will cycle on and off in order to keep your home near that set level.

The Igniter

When your thermostat sends a signal to your gas furnace to turn on your heating system, the first thing that happens is your ignitor starts. Although some older gas furnaces use a pilot light, modern gas furnaces have a safer electronic starter.

The old-fashioned pilot light used to operate by having a regulator supply a tiny bit of gas to keep a small flame burning, which would then ignite the furnace when a Texas homeowner turned it on. If the pilot light went out, you would run the risk of dangerous gas leaking into your home.

The modern electronic starter uses an element a lot like a light bulb filament to ignite the gas burner instead. When your thermostat reaches a preset temperature, the electronic starter sends an electric current over the filament, igniting the natural gas.

The Combustion Chamber

The gas furnaceโ€™s ignitor lights the fuel in the combustion chamber, which is where the natural gas and oxygen mix. Your homeโ€™s furnace uses a draft hood or vent system to take in oxygen in order to generate clean and efficient combustion.

This same vent system releases the combustion by-products through a flue to the outside air. Typically, standard-efficiency flues are made from galvanized steel and high-efficiency units employ polypropylene venting, which is easy to install and maintain.

Itโ€™s important the combustion chamber is properly maintained, so you can ensure your indoor air quality is safe and healthy. You want to be sure all the natural gas is completely consumed inside the combustion chamber.

The Heat Exchanger

Above the combustion chamber, youโ€™ll see the heat exchanger, which takes the heat that rises above the chamber to generate the warm air for your home. Heat exchangers usually use a series of metal tubes, which are heated by burners when gas is consumed inside the combustion chamber.

The hot tubes transfer radiant heat to the air that blows through the exchanger. Once it arrives at the proper temperature, the motor of your gas furnace will turn on and blow that air throughout your air duct system. When the cooler air returns to the furnace, the entire cycle begins again and continues until the thermostat is triggered to turn off.

Blower fans direct the air coming from your homeโ€™s return ducts into the hot heat exchanger for further heating. Some furnaces will have a multispeed blower thatโ€™s programmed when you install your gas furnace.

High-efficiency-model furnaces usually have a variable speed blower that can self-modulate fan speeds. According to the American Council for an Energy-Efficient Economy, variable-speed motors are more energy-efficient than conventional systems.

Some high-efficiency gas furnaces may also contain several heat exchangers with curved surfaces. This design slows down the airflow over more surface area so you can generate more heat with less fuel.

Itโ€™s important to be sure your heat exchanger is in good working order, because a faulty exchanger could allow dangerous leaks into your home.

Contact Us for All Your Furnace Needs

Whether youโ€™re in need of a new gas furnace, a repair to an existing system, or regular maintenance, turn to KCA Services, in Boerne, Texas, for help. Our trained experts provide high-quality workmanship to be sure your gas furnace is operating optimally. Call 210-698-8520 or request service online today.

Why Choose Us?

KCA Services demonstrates excellence by holding ourselves to a higher standard.

Learn More
holding hands icon
BBB Accredited Business
Fully Accredited by the BBB since 1973
ribbon icon
Award Winning Service
KCA Services has been awarded Boerne's "Best of the Best" for 22 years in a row.
people icon
Professional Staff
Our internal motto is "we will always do the right thing."
thumbs up icon
Hassle-Free
We feel being truthful and working to make things right goes a long way.
KCA Services Logo

What Our Customers Say

Amazing Team!

Both Joseph and Josh were amazing in getting my heating system working again. It took some time with pieces and parts but they were persistent and it finally worked! A great team both in the field and in the office. Appreciate the warranty support. You couldn’t ask for more

Rives T.

Prompt and Professional

KCA did a great job for us. They were prompt and professional when they came to bid. Started and ended the project on time with excellent craftsmanship. Highly recommend KCA!!

Rob R.

Very Impressed!

Very impressed with this company. Courteous, professional, and maintained a clean work area while cleaning our ducts. The two gentlemen that came out to do the work represented their company very well!. I would highly recommend this company.

Tim B.